The RMT (Remote Control) module is primarily designed to send and receive infrared remote control signals that use on-off-keying of a carrier frequency, but due to its design it can be used to generate various types of signals.
import machine # create a RMT object for transmission rmt = machine.RMT(channel=3, gpio="P20", tx_idle_level=0) # create series of bits to send data = (1,0,1,0,1,0,1,0,1) # define duration of the bits, time unit depends on the selected RMT channel duration = 10000 # send the signal rmt.send_pulses(duration, data)
import machine # create a RMT object rmt = machine.RMT(channel=3) # Configure RTM for receiving rmt.init(gpio="P20", rx_idle_threshold=12000) # wait for any number of pulses until one longer than rx_idle_threshold data = rmt.recv_pulses()
Construct an RMT object on the given channel.
channel can be 2-7. With no additional parameters, the RMT object is created but not initialised. If extra arguments are given, the RMT is initialised for transmission or reception. See
init for parameters of initialisation. The resolution which a pulse can be sent/received depends on the selected channel:
|Channel||Resolution||Maximum Pulse Width|
|0||Used by on-board LED|
Initialise the RMT peripheral with the given parameters:
gpiois the GPIO Pin to use.
rx_idle_thresholdis the maximum duration of a valid pulse. The represented time unit (resolution) depends on the selected channel, value can be 0-65535.
rx_filter_thresholdis the minimum duration of a valid pulse. The represented time unit (resolution) depends on the selected channel, value can be 0-31.
tx_idle_levelis the output signal's level after the transmission is finished, can be RMT.HIGH or RMT.LOW.
tx_carrieris the modulation of the pulses to send.
tx_idle_level must be defined, both cannot be given at the same time because a channel can be configured in RX or TX mode only.
rx_filter_threshold is not mandatory parameter. If not given then all pulses are accepted with duration less than
tx_carrier is not mandatory parameters. If not given no modulation is used on the sent pulses.
tx_carrier parameter is a tuple with the following structure:
carrier_freq_hzis the carrier's frequency in Hz.
carrier_duty_percentis the duty percent of the carrier's signal, can be 0%-100%.
carrier_levelis the level of the pulse to modulate, can be RMT.HIGH or RMT.LOW.
Deinitialise the RMT object.
If an RMT object needs to be reconfigured from RX/TX to TX/RX, then either first
deinit() must be called or the
init() again with the desired configuration.
Reads in pulses from the GPIO pin.
pulsesif not specified, this function will keep reading pulses until the
rx_idle_thresholdis exceeded. If it is specified this function will return
the exactly that number of pulses, ignoring anything shorter than
rx_filter_thresholdor longer than
timeoutis specified, this function will return if the first pulse does
not occur within
timeoutmicroseconds. If not specified, it will wait
Return value: Tuple of items with the following structure:
levelrepresents the level of the received bit/pulse, can be 0 or 1.
durationrepresents the duration of the received pulse, the time unit (resolution) depends on the selected channel.
Maximum of 128 pulses can be received in a row without receiving "idle" signal. If the incoming pulse sequence contains more than 128 pulses the rest is dropped and the receiver waits for another sequence of pulses. The
pulses_get function can be called to receive more than 128 pulses, however the above mentioned limitation should be kept in mind when evaluating the received data.
Generates pulses as defined by the parameters below
durationrepresents the duration of the pulses to be sent,
the time unit (resolution) depends on the selected channel.
dataTuple that represents the sequence of pulses to be sent, must be
composed of 0 or 1 elements.
start_leveldefines the state (HIGH/LOW) of the first pulse given by
datais not given.
data must be a tuple and
duration can be a tuple or a single number, with
data being optional. In the case that only
duration is provided, it must be a tuple and you must also provide
start_level which will dictate the level of the first duration, the signal level then toggles between each duration value. If
data is provided and
duration is a single number, each pulse in
data will have have an equal length as set by
duration are provided as tuples, they must be of the same number of elements, with each pulse lasting its matching duration.
- Define the level of the pulse: